Structural Support & Jack Posts in Westwood

Westwood was developed mainly in the 1960s on the west side of the city, a consistent neighbourhood of bungalows and split-levels on heavy clay. The original foundations are sound mid-century construction with full basements. Crawlspaces here are the later layer: rear additions, sunrooms, enclosed carports and converted porches added through the 1970s, 1980s and beyond.

These additions follow the same pattern we see across every postwar neighbourhood in Winnipeg. Support was set shallow — often sonotube piers well above the design frost depth — and the clay beneath them freezes to depth each winter and lifts them. Twenty or thirty cycles later, the addition is visibly out of level, the junction with the main house has opened, and the crawlspace underneath is pulling cold air in winter and humid air in summer. With batt insulation between the joists holding moisture against the subfloor, mould on the sheathing is the predictable outcome.

Clay shrinkage in dry summers compounds the water problem by opening a channel beside the foundation for the next heavy rain. Our work in Westwood is typically a combined structural and envelope job: bring support down to stable bearing below frost depth, correct grading and downspouts, add interior drainage only where groundwater actually warrants it, then encapsulate with a sealed barrier, insulate the perimeter, and confirm the space holds humidity through a full year.

Westwood calls are the standard 1960s pattern: a rear addition or enclosed carport on shallow piers, a floor that has gone out of level, doors that bind in deep winter, and a crawlspace underneath with batts in the joists and frost on the sheathing. Owners often mention they have had the tile repaired more than once.

Our first recommendation is to establish founding depth and correct support below the frost line, because repairing finishes above a moving structure is money spent twice. Grading and downspout work follows, then sealing and perimeter insulation. Interior drainage goes in only where readings show groundwater is genuinely active rather than by default.

When a floor over a crawlspace sags, bounces or slopes, the cause is almost always in the support system below it: a beam that has deflected beyond its span capacity, posts bearing on inadequate footings, piers that have tipped or settled, or sill plates that have lost section to decay and no longer bear evenly. Diagnosing which of these is at work matters, because the repairs are different and installing a jack post under a rotted beam simply transfers the problem a metre sideways.

The specifically Manitoba version of this problem is founding depth. Our design frost depth runs roughly 1.8 to 2.4 metres, and anything bearing above that will move as the ground freezes and thaws. Crawlspace additions — sunrooms, family rooms, converted porches, enclosed decks — were very often built on sonotube piers or shallow pads placed well above that depth, because it was cheaper and the consequences take years to appear. Those piers lift every winter and settle every spring. After two or three decades the addition has racked, the junction with the main house has opened, and finishes crack on a predictable annual cycle.

Correcting it means getting support onto stable bearing. For interior posts, that is a properly sized concrete footing designed for the load, with an adjustable steel post bearing on it, shimmed and set so load transfers cleanly. For additions on frost-affected piers, the options are to underpin or replace the piers to below frost depth, or in some cases to install helical piles, which can be driven to stable bearing with far less excavation than conventional underpinning — a genuine advantage inside a tight crawlspace. Which approach fits depends on access, load, soil and budget.

Decay repair usually accompanies this work, because wet wood and overloaded wood go together. Sill plates with section loss at the ends, post bases that have been sitting in damp soil contact, and beam ends bearing in pockets that collect moisture all need to be assessed and either repaired, sistered or replaced. We do this before any sealing work, since there is no sense encapsulating a space and then cutting the barrier open to replace a sill plate. Lifting and shoring during these repairs is done incrementally, because raising a settled floor too quickly cracks finishes upstairs.

We are candid about the limits of what crawlspace support work can achieve. Correcting bearing will stop further movement and can recover much of a sag, but a floor that has been out of level for thirty years will not always come back to flat, and forcing it can do more damage than it repairs. Where we think the right expectation is stabilization rather than restoration, we say so before the work starts. We also flag conditions that belong to a structural engineer rather than a contractor — significant wall displacement, horizontal cracking suggesting lateral failure, or load paths that need design rather than repair.

Load paths are what we are really assessing, and it is worth explaining what that means in a crawlspace. The weight of the floor above travels through joists into beams, from beams into posts, from posts into footings, and from footings into soil. A failure anywhere along that chain shows up as movement at the top. Replacing a post that is standing on a patio slab without addressing the inadequate bearing beneath it moves the problem rather than solving it. Before we specify anything we trace that path from the floor framing down to the soil and identify which element is actually the weak link.

Permits and engineering involvement follow fairly clear lines, and we would rather raise them early than halfway through. Like-for-like replacement of a post and footing is generally routine. Changes to load paths, new structural members carrying significant load, underpinning, and work affecting the building's lateral stability typically require a permit and frequently engineered drawings. In Winnipeg that means a permit application through the City; in surrounding municipalities the process differs by RM. We will tell you when we believe your project crosses into that territory, and we would rather lose a job to that honesty than proceed on a handshake.

Helical piles deserve a fuller explanation because they are unusually well suited to this work in our conditions. The pile is a steel shaft with one or more helical plates, screwed into the ground with hydraulic equipment until it reaches soil capable of carrying the design load. Two things make them valuable in a crawlspace: the equipment is compact enough to work in confined spaces where a conventional excavation is impractical, and installation torque correlates with capacity, so there is a measurable verification of what the pile will carry. In Red River valley clay, where competent bearing can be well below frost depth, that reach matters.