Radon Mitigation in Niverville

Niverville has grown faster than almost anywhere else in Manitoba over the past two decades, which means its crawlspaces fall into two very different groups. New subdivision construction is generally tight, built on engineered fill with modern drainage, and where it includes a crawlspace that space is usually designed as conditioned mechanical area. The problems there are commissioning problems: air sealing never finished at the rim joist, a dehumidifier that drains to nowhere, a sump discharge that freezes, insulation installed to the wrong side of the assembly.

The older rural properties around the town are a different story. Farmhouses and mid-century homes here often have shallow crawlspaces on heavy clay, with soil floors, open vents and whatever insulation was available at the time stapled between the joists. After decades of Manitoba freeze-thaw with moisture present, we find spalled concrete, tipped piers, soft sill plates and mould colonies on the subfloor. Because these properties are on well and septic, there are also more penetrations through the envelope than a city home would have, and they are rarely sealed or insulated properly.

The clay beneath both populations behaves the same way: it swells with spring water, shrinks in a dry August, and heaves when it freezes to depth. Our systems are built to tolerate that movement rather than fight it — barriers that stay sealed when the floor beneath them shifts, piers founded below frost depth so they stop cycling, drainage that handles a fast melt, and insulation detailed to keep surfaces above the dew point in summer and above freezing in winter. We finish with documented readings so the homeowner has a baseline to compare against next spring.

The two housing populations in Niverville generate two distinct sets of calls. New-build owners contact us about performance: a crawlspace that runs cold, a dehumidifier that stopped working, a sump discharge that froze, insulation that was installed in the floor joists instead of on the walls. Owners of older rural properties call about conditions — damp soil floors, failed insulation, mould on the subfloor, tipped piers. The first group needs commissioning finished; the second needs a system built from scratch.

On new construction we are often asked whether a builder should have done better. Usually the honest answer is that the work met the minimum and the details that matter in our climate were not part of the specification: continuous air sealing at the rim joist, insulation in the correct plane, a barrier mechanically terminated at the wall, a dehumidifier with a permanent drain, and a discharge line that survives minus 30. These are not expensive additions. They are simply not standard, which is why we end up finishing them.

Our first recommendation depends on which group you are in, and an inspection will tell you quickly. For a newer home, the fix is usually targeted and relatively modest — complete the envelope, correct the insulation plane, make the mechanicals winter-reliable. For an older rural property, start with founding depth and framing moisture readings, because those determine whether you are looking at a sealing project or a structural one.

Radon is a naturally occurring radioactive gas produced by the decay of uranium in soil and rock. It is colourless and odourless, it moves upward through soil, and it enters buildings through any opening in contact with the ground. Health Canada identifies it as the second leading cause of lung cancer after smoking, and sets a guideline of 200 becquerels per cubic metre for indoor air, recommending remedial action above that level. Manitoba consistently records some of the highest residential readings in Canada, which makes this a local issue rather than an abstract one.

A crawlspace is the most efficient radon entry point a house can have. Where there is exposed soil, or a thin unsealed membrane, soil gas moves into the space essentially unimpeded — and from there into the living area, because the stack effect pulls air upward through a house continuously during the heating season. Our long heating season means that pressure difference operates for a large part of the year. A house with a sealed basement slab but an open crawlspace under an addition can still have substantially elevated levels.

Testing has to come before mitigation, and it has to be done correctly. A long-term test of at least three months, ideally during the heating season when windows are closed and the stack effect is strongest, gives a representative result. Short-term tests are useful as a screening indicator but fluctuate too much to base a decision on. We will arrange or guide testing, and we would rather you test first than buy a mitigation system you may not need — though in a crawlspace with exposed soil, sealing the floor is worthwhile on moisture grounds regardless of the radon number.

Where mitigation is needed, the standard approach in a crawlspace is active sub-membrane depressurization. A sealed membrane is installed across the floor and up the walls — the same membrane used for encapsulation, which is why these two projects belong together — and a dedicated fan draws continuously from beneath it through a perforated collection pipe, venting above the roofline. That negative pressure under the membrane captures soil gas before it can enter the space. The system is simple and highly effective, but it depends entirely on how well the membrane is sealed, which is why installation quality matters more than equipment selection.

Post-mitigation verification is not optional in our view. After the system is running and the building has returned to normal operating conditions, the space and the living area should be retested to confirm the reduction. We also label the system, explain what the manometer reading means, and tell you what to check — because a mitigation fan is a mechanical device that will eventually fail, usually silently. A system nobody monitors is a system that may have stopped protecting you years ago.

Pressure and building dynamics explain why two apparently identical houses can test very differently, and why your neighbour's result tells you nothing about yours. Radon entry depends on the pressure difference between the soil and the building interior, and that depends on stack effect strength, exhaust appliances, mechanical ventilation balance, wind, and how tight the building is. A house with powerful kitchen and bathroom exhaust and no make-up air runs at a greater negative pressure, and draws correspondingly more soil gas. This is also why sealing work and mechanical changes can shift a reading in either direction, and why testing after any significant envelope work is sensible.

System design details separate a mitigation that works from one that merely hums. The collection point beneath the membrane needs a permeable layer — clean gravel or a drainage mat — so the fan can draw from the whole footprint rather than a single spot. The fan has to be sized to the soil's permeability and the area served: too little suction leaves parts of the footprint uncaptured, too much wastes energy and can pull conditioned air if the membrane has gaps. The exhaust must terminate above the roofline and away from windows and air intakes. And the pipe needs a manometer, so the system reports its own status.

Timing relative to encapsulation is the practical advice we give most often. If you are sealing a crawlspace for moisture reasons and you have not tested for radon, test first. The collection pipe and gravel layer belong under the membrane, installed before it goes down; retrofitting them means cutting open a barrier you just paid for and compromising its continuity. A long-term test takes three months, which is usually compatible with planning a project anyway. If the number comes back low, you have lost nothing but gained a documented baseline. If it comes back high, you have saved yourself from doing the job twice.